Відео

Fantastically clear video and instructions. thank you!

Fantastic video on how to replace the heating element on a Samsung dryer. I was very apprehensive about removing the drum but your video picture of this was extremely helpful and I was able to successfully do it. Can't tell you how much I appreciate your detailed instructions. Thank you!

I found a paint key was a great tool to make sure the felt sat correctly on reinstall

My ice maker doesn't have the same face. The ice maker is sending 25 vac to valve all the time. Sends 120 vac for nine seconds but, valve doesn't open/close . Is it supposed to have 25 v on all the time?

Can any size glass work?

watch the wires when you put the evap fan back, they can hit the blades, then you can take the cover on and off five times trying to figure out whats making the new noise haha

My dishwasher hasn't been washing properly and fill up with a little water but not as much as it should or needs. It doesn't get enough water to spin the arms. My model is a whirlpool mdb4100aww, any thoughts of what might be causing it?

You call that "a very easy repair"!!!! Really?!!!

Not so easy with the short fat ones😏

Expert? Your transition strip is exposed on the other side of the door. This video isn't helpful at all. Thanks for trying though

Those are not factory hose clamps.

Also wanted to comment showing the channel made a big difference. Appreciate that extra effort, helped me a lot.

My question is: why the heck are these so expensive? For two racks I'm half of the way to a new dishwasher.

Very helpful. This was exactly the issue I was having.

Can I see a pic of the belt on motor & idler pulley?

can yu changebtonthe old ones?

If my Ice Maker. Is at the bottom Does that mean that's where the reset button?

My ice falls from the bottom.

My ice Maker is at the bottom.

What are the sounds of bad spin bearings in a Whirlpool direct drive washer?

Your dryer motor video helped me out tremendously, thank you for your channel! Saved lots of money$ too.😉👍

Thank you very much. This was very helpful.

Great vid

Followed your steps and it went perfectly. Saved about $350 in parts markups and labor. Was $27.00 for controller on Amazon.

The room air passing through the evaporator isn't "chilled". The heat in the room air is absorbed by the evaporator.

First time in the fridge and it was easy! THANK YOU !!

Thanks !!

𝙊𝙠😊

My gasket doesn’t overlap like that the slots are much farther apart 5 - 6 inches maybe seems like a design flaw in my model

I have a stove similar the one in this video and it is the biggest burner that isn't working. It won't heat up. I replaced the switch and also replaced the burner and am still having the same problem. The burner won't heat up. Does anyone have any ideas on what the problem might be?

All of the tops you didn't orient the ball right. The top hooks set down in the ball

How did you remove the lower drawer on the oven I have that same stove, but can't get it out?

My brackets go from front to back and not from left to right. This makes it very difficult if not impossible to remove the bracket being that the screw that holds the bracket in place is at the rear. Does anyone have any ideas?

2:00 Problem here is, there are no wire harnesses to disconnect. The wires go straight to the burners. The brackets that hold the burners in place go from front to back just like in your video with the screw that holds the mounting bracket in place being at the back of the stove top. This makes it difficult if not impossible to remove the bracket. If the brackets went from left to right, this would make it much more user friendly. I am going to continue on and try to do this, but it would be nice to be able to remove the whole top like you do in the video.

I went on the Whirlpool website to purchase the large failed burner and found out all the burners are about $96.00 except for the one large burner that I need. That one, including taxes and shipping is $280.00!..... but still better than paying a repair person or buying a new stove.

I like the _soothing music_ in the background, it helps to destress me. I also like the clear closeups so I can see what you are doing.

Does the clutch stop agitating ?

Thanks dude

I gotta say this was a good video, BUT, I HATE HATE HATE the background music!! It was SO DISTRACTING! Who did you let ruin your great repair video with that stupid distracting "canned" bongo drum and geeeeetarrrrr music?! I had to keep stopping and rewatching several parts of it. Hate to say it but it ruined your video that has a lot of information and is difficult to follow anyway because of a LOT of info. Not even going to save it. Too painful. You should re-release the video with no background music.

This is a really pos dryer. So sorry I bought it.

Thank you so much, this was so helpful!

I'm so grateful for the detailed clear video ...my appreciation for you, boss 🌹

This is perfect. Just what I needed to feel like I could handle it.

Excellent video tutorial. I did a deeper dive replacing both valves and the drain pump and this video was really helpful! Thanks

It’s just like mine except for I don’t have the four screws holding the fan cover so I’m still searching for a video on how to do this. Very well done video just not mine.

I hate those new ones

Thank You! Man I LOVE UA-cam!!!

Thank you sir

Were can I. Find it in vredenburg

What direction should this fan be spinning please, should it be blowing towards the coils or pulling air over the coils and blowing out the back?